Vehicles
75 not categorized PORSCHE 911 FLUIDSCan't find what you need? Try browsing the Accessories or Exploded Diagrams!<-- Try narrowing by car using the menu to the left.FVD351997GT2CS This kit convert's the 997 turbo GT2's / 997gt3 rs pccb rotors to 997 GT3 cup car steel rotors with green cup car pads. This system is complete with everything that you need to install. Do not ruin your expensive ceramic brake discs on the track. Get ready for racing with the original and much cheaper Porsche motorsport steel brake discs! What's in the box: 4 x brake discs (380 x 34 mm - front / 350 x 28 mm - rear) 4 x wear sensors 2 x cup brake pads (racing green) 8 x screws for brake caliper 8 x damping plates technical tip: also order stainless steel brake lines (FVD b96 355 97) and racebrake fluid (012 145 ca). General Fitment911 GT3 2007-11911 TURBO/GT2 2007-09
From $3,335.20
Make a selection 91131802900 If your speedometer completely fails look at the angle drive first before suspecting the cable. easily checked by disconnecting the speedometer cable then lifting the car and putting it in gear to see if the angle drive spins, the part is easily replaced. always try to buy a new one as this is a wear part. purchase a speedo angle drive seal at the same time to stop the transmission fluid leak. it fits on the drive gear in the rear tail cover and is easily removed with the rear 13 mm headed set screw. You will have a fluid spill when this is removed so get ready! Refill with 80/90 weight oil only. View/Change Diagram
From $52.47
Make a selection 95037013 Stoptech brake lines consist of a ptfe (commonly referred to as teflon) inner line that carries the brake fluid, which is then covered with a layer of stainless steel woven braid. The ptfe tube is very resistant to expansion under pressure and will not degrade from exposure to brake fluid. every stoptech brake line is 100% tested in-house to a pressure of 4,500 psi. This is almost 4 times the typical line pressure exerted by a production vehicle's master cylinder. stoptech is a registered brake line manufacturer with the united states DOT and all stoptech stainless steel brake lines are manufactured to meet DOT compliance standards. Stoptech stainless steel lines also meet or exceed fmvss 106 and applicable...(choose a part on the right to read more) General Fitment911 2009-12911 1998-05 911 2005-08 911 GT3 2003-05 911 TURBO/GT2 2001-05 911 TURBO/GT2 2007-09 911 GT3 2007-11 911 TURBO/GT2 2010-13 CAYMAN 2009-12
$63.42
Make a selection 95037003 Stoptech brake lines consist of a ptfe (commonly referred to as teflon) inner line that carries the brake fluid, which is then covered with a layer of stainless steel woven braid. The ptfe tube is very resistant to expansion under pressure and will not degrade from exposure to brake fluid. every stoptech brake line is 100% tested in-house to a pressure of 4,500 psi. This is almost 4 times the typical line pressure exerted by a production vehicle's master cylinder. stoptech is a registered brake line manufacturer with the united states DOT and all stoptech stainless steel brake lines are manufactured to meet DOT compliance standards. Stoptech stainless steel lines also meet or exceed fmvss 106 and applicable...(choose a part on the right to read more) General Fitment911 1965-69911 1970-73 911 1974-77 911 1978-83 911 1984-86 912 1965-69
$91.60
Make a selection 91157393903 A failing receiver dryer can be identified by the internal chambers of the unit beginning to rattle during operation. You may also experience refrigerant leakage near the fittings or small pools under the car. These issues should be addressed as quickly as possible to prevent further damage to the system. High-quality OEM replacement, designed to perform like the original. We source this part in Germany to ensure quality, reliability and precise fitment. Sold individually. 1 necessary per car. View/Change Diagram
From $35.43
Make a selection 95037504 Stoptech brake lines consist of a ptfe (commonly referred to as teflon) inner line that carries the brake fluid, which is then covered with a layer of stainless steel woven braid. The ptfe tube is very resistant to expansion under pressure and will not degrade from exposure to brake fluid. every stoptech brake line is 100% tested in-house to a pressure of 4,500 psi. This is almost 4 times the typical line pressure exerted by a production vehicle's master cylinder. stoptech is a registered brake line manufacturer with the united states DOT and all stoptech stainless steel brake lines are manufactured to meet DOT compliance standards. Stoptech stainless steel lines also meet or exceed fmvss 106 and applicable...(choose a part on the right to read more) General Fitment911 1989-94
$63.42
Make a selection 99906402002 High-quality OEM (original equipment manufacturer) replacement, designed to perform like the original. We source this part in Germany to ensure quality, reliability and precise fitment. Sold individually. 1 necessary per car. Please note: please check the model fitment tab to ensure accurate fitment. View/Change Diagram
From $14.50
Make a selection AP993410 Agency power now has a wide variety of steel braided brakelines for most high-end performance cars. The brakeline kits are made in the usa to meet strict d.o.t. Certifications. The steel braided lines are a smoke color with the ap logo printed on it. The cnc machined fittings are in classic agency power gold to separate you from the competition. All kits are assembled for a quit and easy install. Include fittings, hoses, and necessary hardware. General Fitment911 1994-98
$69.95
Make a selection 95037502 Stoptech brake lines consist of a ptfe (commonly referred to as teflon) inner line that carries the brake fluid, which is then covered with a layer of stainless steel woven braid. The ptfe tube is very resistant to expansion under pressure and will not degrade from exposure to brake fluid. every stoptech brake line is 100% tested in-house to a pressure of 4,500 psi. This is almost 4 times the typical line pressure exerted by a production vehicle's master cylinder. stoptech is a registered brake line manufacturer with the united states DOT and all stoptech stainless steel brake lines are manufactured to meet DOT compliance standards. Stoptech stainless steel lines also meet or exceed fmvss 106 and applicable...(choose a part on the right to read more) General Fitment911 1989-94911 1994-98
$91.60
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |